The Graphical User Interface software is windows based and is supplied free of charge after the installation engineer has been on an Intellitec certified course.The software has been designed to be user friendly and the amount of parameters that can be programmed is almost endless. There are also two programmable 10A outputs that can be used to switch external alarms or indeed what ever may be specified. To restart, simply press the reset switch and starting power is restored.Īutomatic reconnection is also possible in specific applications via the software.īuilt into the Battery Guard 3000 is a programmable audible alarm, this can be linked to both voltage and time. Applicants should contact their local PG&E. This ensures that starting power is preserved. Applicant gas and electric service and meter installation arrangements are subject to. If the battery voltage drops below a pre programmed level of both time and voltage, the system isolates all electrical loads that are connected through the battery guard relay. Remplacer par un fusible retardè de même type et de 2.5 ampères 250 volts.The Battery Guard 3000 is a fully programmable power management system that can be programmed to a customers requirements.īattery Guard 3000 operates by constantly monitoring the available battery power when the engine or charging source is not active.Ĭut out voltage`s, timers & alarms are fully programmable to provide a fully flexible solution. Remplacer par un fusible rapide de même type et de 1 ampères 250 volts. Replace with the same type 2.5 ampere 250 volts slow acting fuse.Įxplanation des symboles de fusible utilisés dans l’appareil Replace with the same type 1 ampere 250 volts quick acting fuse. Place the battery exactly like the old one.Įxplanation of the fuse symboles used in the set
#BATTERY GUARD 3000 SERVICE MANUAL MANUAL#
Use only batteries at the same make and type as mentioned in this service manual (see page 3.1). When replacing the lithium battery in this set, note the following: Short-circuit and overcharging of some types of lithium batteries may result in a violent explosion. The apparatus must be opend by qualified servicemen only. The black and yellow label on the compact disc player serves as a warning that the apparatus contains a laser system and is classified as a class 1 laser product. The new component must be mounted in the same way as the one replaced. When replacing components with this symbol, components with identical part numbers must be used. Three different ground symbols are used in the set. The bend of the wire indicates in wich direction the other end of the wire is found.Ī connection to another diagram page is indicated by a number as well as by a letter of the diagram to which the connection leads.Īll supply voltages in the diagrams are indicated by an arrow and a voltage indication. Remove the bottom cover (see Bottom cover on page 26). ’ Programming To start the program mode a connection should be made between the Input+ and the ProgramInput. Prepare the computer for disassembly (Preparation for disassembly on page 25). Fitting and use of the Battery Guard (BG) takes place at the users risk. Internal connections on a diagram page are indicated by a number. connection which is connected to the battery via a fuse of 1A. The individual wires are provided with one of the following codes: The wiring connections on the diagrams are assembled in ‘bundles’. In certain control circuits the active mode is indicated by a function term or by an abbreviation. The coordinate numbers are written in smaller print types than the position numbers. This indicates in which coordinate on the PCB the component is situated. On the diagrams every component has a coordinate number. The largest PCBs have component prints and a coordinate system on both the print and the component side. If the position is followed by an asterisk the spare part number must always be used because the component in question has been specially selected, e.g. Type numbers of transistors and ICs are indicated on the diagrams. Supply voltage 7V > 15V, stand-by 3V > 15VĢ.1 Explanation of diagram Explanation of diagram Supply voltage -7V > -15V, stand-by -3V > -15V Test of Master Link DATA receiver/transmitterĨ0 - 72 dBµV/m (10 - 4 mV/m) TYP 4mV/meterĦ8 - 60 dBµV/m (2.5 - 1mV/m) TYP 2mV/meter.TM (test mode) names/function for adjustments and service.PCB20, 8005738 IR receiver and left door sensor.PCB14, 8001771 Master Link Audio interface.
PCB20, IR receiver and left door sensor.Diagram F – Light and Motor control, Light supply & IR.Diagram C – Stereo decoder and power section.
0 kommentar(er)
